New Camo Dipping special

[Blackhawk7204]

Hey Terry, your bow got here today.

[BMG]

Thanks Lonnie, just picked up the riser today.  It looks great.

[Blackhawk7204]

Glad you like it.

[Blackhawk7204]

Hey Terry, Your bow is ready! Check it out!

[owlbait]

Sweet job Lonnie, got mine in the mail to you today. Check is in the box.
Thanks Mike Gerard  owlbait

[VA Bowbender]

Lonnie,
I didn't read every post so this might have been asked. What is the general turnaround time to do a bow?
I have a Bear magnesium take down I'm thinking of having you do. I think I'd like the handle done in Carbon Fiber and the limbs done in Leaf and Woods Mix. Is there an extra charge for two different prints? Would I have to do any prep work like sanding off old spray paint from the handle? I know I should take off the latches, window sight plate and side plate and grip, etc. Should I do anything else?

 

[red44]

Originally posted by wingnut:
I sure like that carbon fiber pattern

we have a warf bow from a customer that we are doing ILF limbs for that is a canidate for that one.

Mike

That would work Mike.  

[Blackhawk7204]

VA Bowbender, turn around is 1-2 weeks. Just take the stuff off and I'll take care of paint.
No extra charge for 2 different patterns, just be sure to put a note explaining how you want it with your bow.

[Kenneth]

Lonnie,  I'm gonna be sending another one your way.  My wife saw a carbon fiber looking bow at K-zoo and loved it so I'll give her an early Anniversary present.

Terry's bow looks great!  Hope mine turned out looking like that too!!  

[VA Bowbender]

Originally posted by camodip:
VA Bowbender, turn around is 1-2 weeks. Just take the stuff off and I'll take care of paint.
No extra charge for 2 different patterns, just be sure to put a note explaining how you want it with your bow.

Thanks, it will be in the mail today.

[Blackhawk7204]

Kenneth, your bow looks just like Terry's but I forgot to take pictures. Too late now, I shipped it out yesterday.

[Kenneth]

that's great!  I better call Jim today and let him know.  Can't wait to get her back!  I'll be sending out my wifes Ben Pearson "Varsity" today or tomorrow to get a carbon fiber dip.
thanks Lonnie!

Ken

[SkottyBoy]

Does the process have any effect on the original preformance of the bow, i.e. heavier draw weight??? And have you ever dipped a Black Swan with the metal riser? It really has a lot of "dimples" in it.  Thanks

[VA Bowbender]

Ok, here's some pics of the Bear magnesium riser and limbs I sent off to Lonnie.  I asked him to do the limbs in a burl and the handle in a carbon fiber. I did tell him if the burl wasn't one I cared for he could substitute for a camo pattern.

When the bow comes back I'll post the end result.

  I got this bow used, I didn't do the damage. Someone made a really poor atempt at refinishing.

[Blackhawk7204]

SkottyBoy, I've never seen any difference in performance. Even on A&H ACS limbs.
That dimpled surface you're talking about is just the paint. The metal underneath is smooth.

[ckanous]

Lonnie I have a warf bow I'm finishing up on and when its ready can I send it or need to call and set up a time to get it to you first, how does this work basically? Nice looking work by the way.

[Blackhawk7204]

ckanous, Thank You.  You can just send it in along with a check and a note explaining which pattern you want. Address is on the website.

[ckanous]

Sounds good I'll have it ready to go before long. Thanks

[Kenneth]

Lonnie,  I mailed out my wifes bow yesterday.  It should be there today or tomorrow.  I wrote on it which end to open cause that's where the order specs and MO are.

thanks again,
Ken

[Blackhawk7204]

VA Bowbender, Your bow got here today. WOW, that bow is pretty bad but I like a challenge! The paint on that riser is not only peeling off but the metal has corrosion.
Nothing I can't handle though, stay tuned for further updates.

Kenneth, not here yet. Probably friday.