Main Menu

form material

Started by bbs383ci, March 27, 2012, 03:13:00 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

bbs383ci

i have a binghams recurve and longbow plans, i need to some forms, i recently bought a very straight 2x8 to try it for the longbow since it is 1 1/2" wide, it was also treated i dont know if that makes difference, does anyone have a problem with a form like this twisting while it is in the oven, it not how do you stabilize it to keep it from doing so, or is there another alternative besides plywood for a form.

thanks

dmikeyj

LVL lumber, MDF, Corian have all been used effectively.
Imagination will often carry us to worlds that never were. But without it we go nowhere.
I love fools' experiments. I am always making them.

bbs383ci


bbs383ci

well i have called all of the places in my area that can get lvl and all they can get is 1 3/4" wide, do yall know of any place else that you can get this stuff from that has diffrent thicknesses available?

Glunt

I would go with your board.  Natural grain is susceptible to  changing more so than laminated stuff but it may be fine.  I've seen a bunch of guys use a single board like that.

If it does start to tweak, you can add some runners down the side to make it behave.  I would pop it in the oven for a couple hours and see what happens.

If you grab some of that 1 3/4" LVL, you should be able to find some 1/4" stuff to add to one side and get 2" before cutting your form out.

bbs383ci


Robertfishes

I live in a high humidity area So I would not use a board, I would worry about it twisting when heated, pressure treated wood will be more likely to twist..at least the PT Pine boards we have here in Florida, the PT wood here usually has a high moisture content.
Many guys use the LVL and it must be pretty darn good stuff. For the 1 1/2" form you can sand the 1 3/4" down to 1/1/2" if you have a big enough sander..I don't, but my neighbor has a CNC machine at his Cabinet shop that would do it..I use Cabinet grade birch plywood from the neighbors Cabinet Shop, I bought enough 3 years ago to make 4 form blanks, Then I found out about the LVL...Good luck with your builds!

jsweka

You could get two 3/4 pieces of plywood and laminate them together with tite bond and wood screws.  Depending on how close the plywood actually is to 3/4, you might have to add another piece of 1/4 in the middle.
>>>---->TGMM<----<<<<

Robertfishes

John, thats what I ended up doing on my 4 forms, I used my digital calipers and found I needed a thin piece..so off to Lowes with my digital calipers.. I went thru a bunch of thin pieces of plywood, paneling etc and found a wood door skin that was the right thickness to make the form 1 3/4" wide. I put the door skin in the middle of the stack. This is a 1 1/2" wide form I made using 3 pieces of plywood.  

scottm

What about adding a 1/4" piece of ply or luan to the 1-3/4" LVL? Just a thought.

Dmaxshawn

Dusty I'll send you a pm on the green screen.  I have a form that I don't use anymore. I'd be willing to send to you.  

Shawn

bbs383ci

sweet thx shawn ill take a look.

7 Lakes

A piece of formica will take up the extra space you need, just rough up the smooth side before gluing.  That's for for a 1.5" form

Bowjunkie

A concern with particleboard... it's not nearly as strong as plywood. I had a particleboard recurve form explode in the oven once. I never used the stuff again.

Now I only use plywood glued and screwed together, or LVL lumber.

arrowlauncherdj

You can use particle board for the base form since it is very straight and sands nice. Then laminate it on the sides with some thin ply like 1/2" on each side dropping it down low enough to allow you to put on your washers to hold everything straight.  Also that adds a nice spacer for your air hose to keep it from pressing on your form hardware.

johnny girardi

I have on my last bow forms used what we call microlam beams or gluelam beams. you can find then at 84 lumber,Menards by me not sure in Tx. These are multy laminated beams of soft whitewood.I just pick them up and look down board for streightness. they are only 1.75" wide.I never had one warp on me.


Contact Us | Trad Gang.com © | User Agreement
Copyright 2003 thru 2025 ~ Trad Gang.com ©