Hi Gang I have built a Bamboo backed bow and would like some advise. The Tiller seems to continue to change the more I draw it. I have about 2 & a half inches of set. But the real problem is the upper limb bends more in one spot the the other. I am thinking about thinning out the limbs and adding a belly to bring the weight back up.
So what do you think.

Serious hinges on that one.  It looks like you need to get the limbs bending much more mid limb to the handle.  And don't draw it with those hinges like that.

Well it looks like a great start..here are my suggestions...you will definelty reduce the weight a bunch to get the tiller right but that would be better than a broken bow...you might be able to temper the belly to get the weight up a bit, to chop off an inch or two after you get it tillered.  

So to tiller that better, imagine more of a circular tiller (right now it is extremely eliptical).  I tried the point this out...sorry its a little sloppy (and hinge is spelled incorrectly)

Good luck

 

Like said above get the inner limbs working more. Get the tiller right first. You can add a belly slat later and retiller to get your weight. I have successfully done it on two bows.
  What wood is your belly?

Yikes, those are some serious hinges.

You need a tillering gizmo.

Here is how to make one.

http://tradgang.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=125;t=001047

Thanks guys I will try everything. Eric I will start on a gizmo Thanks.


Sorry I for got the question

Ok I have 2 boards I can cut down for the belly Witch would you recommend. I have A nice piece of walnut and also a nice piece curly maple. Both have a great end grain and flat grain pattern.

Find a belly wood that is strong in compression like osage or ipe.

Curly maple definitely does NOT have flat grain.  If it did, it wouldn't be curly maple.  Good for risers and veneers under glass, but not for anything that'll be working.

Get the tiller correct (and the belly flat) then add the belly wood if you really want a heavier bow.  It can be done, but it'd be easier to just make a new bow.  Like Pat said, osage or ipe would be great (you can get ipe flooring boards from most big lumber yards/hardware stores), but a really good piece of maple or even oak would be fine.  Walnut seems to be real sensitive... if the tiller isn't spot on you'll have problems.

Ok guys here is a shot after retillering. What do you think?

Much more to be taken off the area fades to mid limb, but better.

Start with the basics.

Trim that riser down.  Get it working closer to the handle.  Think circular tiller.  After you have a few bows under your belt, you can start playing with big risers and a cut in shelf.  But you have to learn how to tiller first.  Tiller is everything in wooden bows.  EVERYTHING.

I highly recommend getting the first Traditional Bowyer's Bible.  Many libraries carry it or you can find used ones pretty cheap.     It\\'s $15.61 on Amazon Right Now!

That would be a heavy duty eliptical tiller.  Meaning way over done eliptical tiller.  
John is right, it needs to bend closer to the fades.  You will probably be under draw weight by the time it is correct but that is the joys and trials of wood bow building.  The Traditional Bower's Bible 1 is seconded as the manual to go to.

I would like to know some more info on your bow there.. Is that a all wood lam bow or is that glass and what is your core wood... What glue did you use to glue it up with....

Cody

Thanks guys I'll keep working on it.
As for the Bibles I have vol. 1 thru 4.
Still reading 4

Cody the 3rd picture shows The Red oak and Bamboo
The glue was Titbond III

Well I just thought I would add some more shots to see what you think.

Putting those clamps in the fade area will not give you a clear picture of the tiller. That bow needs to bend into that area and the clamps will stop that. Try to make a cradle that will fit the handle area and recheck the tiller. It isn't broke so still has potential. Keep working at it and a good bow will present itself.

Thanks Razor but the clamps are clamped to the fence not the bow. The bow is just hanging on them.

Both limbs seem to bend pretty well, I just can't stand to look at that riser, it's way too long for my tastes. You did well to get the limbs evened out.

Still way too hingy at mid limb. I will send you a gizmo if you want one.