This will truly be a "build-along" since I was cleaning the freezer out just yesterday and found 3 deer hides.  I'd seen this style of quiver made on another site, although no pictures were included - this will be a learning experience for all.  This uses hair-on deer raw-hide with borax rubbed in for preservative.  No oil is rubbed in so the quiver stays stiff and keeps its shape.  Step one: Beat the dog...she ate one of the hides I had thawing - least I still have two more.  Actually one good hide would probably do, but two is good.  Anyway, step 1-A: Flesh out one side of the quiver:
 

Step 2: Have the forms magically appear -

 

The form for the quiver is made of a 2x6 however long you want your quiver.  This was about 24 inches long.  Taper the 2x6 down to about 4" on the bottom end - rounding it in the process.  I used a router to radius the edge.  Screw it to a scrap piece of plywood.  On a similar piece of plywood, cut out the stretcher.  It will be the same shape as the form but slightly oversized.  I probably cut it with too much slop, bout 1/2" around.  1/4 would have probably been better.  I used the band saw for speed and screwed the form back together, a saber saw would do well...but slower... for cutting out the stretcher.

Step 3: Rub borax into the back of the quiver and tack it to something to dry - the neighbor's fence for instance...
 

This half will dry before you shape it - I left the tail attached, may have it hang off the bottom - we'll see how it works.  The body of the quiver will be formed wet, prepped with borax as well before clamping it into the form.  
 

Hope this works...    
  :rolleyes:

Once the borax was rubbed in, I folded over the top edge of the quiver for some additional stiffness, making sure a good dose of borax was inside.  Hopefull it will cure.  Then I stretched it over the form, stapling it to the base plywood well away from the 2x6.



Now the stretcher is clamped over the form, pulling the hide tight while it is screwed into place:



Run some drywall screws into the plywood to lock it down:



I smoothed out the hair, and now we sit and watch it dry.  With the cold, dry air, hopefully won't take too long.  I put a fan on it just to speed it along.  See you next weekend!  Steve

I'm watching, this looks cool. This would work with other mammals also right???

very intrigued. Thanks for sharing
Kyle
anxiously awaiting your next post

Full quiver - I guess it would.  Not sure how thick a hide would be cured by the borax.  I will say I shaped and dried a turkey skin and fan for a wall hanging close to 10 years ago with borax and it has held up well, even in a humid Georgia garage.  We'll find out soon enough.  Steve

How many squirrel pelts would you need to do this?  :p

One for each arrow.        

Looking good.
PS; Wouldn't carry that thing on my back during gun season! LOL

I agree with you, Carpdaddy - unless I paint it orange!.  I use a bowquiver for hunting anyway.  This'll be for fieldpoints -

Maybe this could be moved TTT or over to the how-to when completed.  I am waiting to see the finished product.

Looking good, SOS! Can't wait to see the finished product! Thanks for sharing!                

Nigel

The stuff I see and learn on tradgang continually amazes me.  Can't wait to see how this quiver turns out.

hey sos this is a good thread man well  done

Hmmmm .... I just so happen to have a couple of fresh hides in the deep freeze here.  Have to keep an eye on this one.

Good thread, wonderful writing style and I like your work habits. Good neighbors make good fences, right?  

nice job ( are drywall screws traditional        )

Well, how long's it gotta dry?  Any finished pictures yet?

Looks like it will be pretty darned nice.

I'm baa-aack.  Few more steps in the right direction.  Things looking okay, but a few lessons learned as well.  Here is the raw hide out of the form, along with the flat piece:



I pulled the hide out of the form and am letting it dry out a little more - as I stated earlier, I probably should have cut the stretcher with a little less slop, but should work okay.  Second, drying the flat piece on the neighbor's fence, not such a good idea unless you live in the dessert.  It did well, but we had some off and on rain.  I finally pulled it off, thinking it was good and dry, but when it continued to dry without being stretched, it it puckered a little and isn't as flat as I would have liked.  Find a way to dry it stretched flat inside!

Next thing I remember was to do a little sanding, especially on the part that will fit against your back to smooth out the rough spots - gently so you don't go through the hide:



Hope to do a little trimming and layout tonight.  Right now, back to detailing an old car for my daughter's 16th B-day.  Last time I wash it!

Some more progress this evening.  Marked out the quiver, leaving about a 1/2 inch lip that will serve to "sew" the two halves together.



Tin snips work pretty well for trimming it.



I may be working too hard at trying to get it to keep it's shape, but just keeping it lined up...



Made a cardboard template to play with.  Remember, when marking on the skin side of the back piece of the quiver, it will be backwards....if you know what I mean.



For the strap, I'm using a $1 leather belt from GoodWill.  Excellent source of leather belts (for knife handles, too).  Using some cloth to work up a template to test out the fit.

Ask questions if it is confusing....



More to come.....  

Darn...now I'm gonna have to try this too...I'll never finish all of these projects.  Daryl