3Rivers Archery


The Trad Gang Digital Market












Contribute to Trad Gang and Access the Classifieds!

Become a Trad Gang Sponsor!

Traditional Archery for Bowhunters




RIGHT HAND BOWS CLASSIFIEDS

LEFT HAND BOWS CLASSIFIEDS

TRAD GANG CLASSIFIEDS ACCESS


Main Menu

Help me with Bare Shaft Tuning

Started by Mint, December 09, 2025, 11:06:00 AM

Previous topic - Next topic

Trenton G., BAbassangler, trad_bowhunter1965, GWomack, Stringwacker, Cove-Creek, Mike Bolin, Tyler Worstell, Tajue17, Buckeye1977, Rob DiStefano, 4dogs, Jim Wright and 17 Guests are viewing this topic.

Mint

Normally I just play with the point weight to get my arrows flying well but I've got some arrows that are for a heavier bow that i would like to use out of my lighter bow with a heavier point for my hog hunting trip. I would like to try bare shaft tuning but I'm a little confused on which method to use. I see Ken Beck has a video where they shoot at a bullseye and adjust the point weight to get arrows hitting dead center as opposed to hitting left or right. Then I see other videos where you study how the arrow actually sticks in the target whereby if shaft is pointing left or right will determine whether to add more point weight or less.

Which method works best or does it not matter? Thanks
The Constitution shall never be construed... to prevent the people of the United States who are peaceable citizens from keeping their own arms.

Samuel Adams

NYB Life Member
NRA Life Member

Tajue17

I go by flight,,, if you dont already have a bareshaft carefully scrape the fletching off one arrow,, hold bow perfectly vertical at about 10yrds away from target and try to be sure everything with your form is perfect especially even tension on string holding fingers,,,,,, tell us what you see when you shoot that arrow a few times..
"Us vs Them"

BAbassangler

I've shot bareshafts Olympic style at a vertical line, into a solid target (for tail direction), and fletched shafts until they just behaved...bareshaft at 15-20 yds is my favorite.  20-25 might be better yet, because targets can fake you (and your eyes too) out by pulling it straighter than what it was flying when it hit the target.  So for me a bareshaft on a tight bale of hay wins.

Jumping up in spine can be a challenge as well too.  My only luck was to run them longer than my usual, or REALLY load up with point wt until it flew straight...at that point they were finicky with consistent draw/flight...my  best success so far, was with 400's when I usually shoot 500's.  I had to use a 'nubby' little, short 50gr half out...seemed to let the stiffer arrow bend easier.  With 100gr and longer inserts I could only build 700+ gr arrows; now down to 630.
I pity da'fool...that rejects Christ.

62" ILF, 40# Bosen recurve limbs on 19" Deerseeker riser
62" ILF, 45# Bosen longbow limbs on 17" Discovery riser
66" Kodiak Special 38#

Arctic Hunter

I go off arrow flight. If you're having trouble seeing it, have somebody stand over your shoulder with an iPhone and video it in slow motion.
It's gotten to the point where basic common sense, about a lot of things these days, doesn't make a lot of sense to most people.
-Phil Robertson

Stringwacker

I bareshaft with one shaft and watch the tail position in flight...and adjust as needed.

I've tried the three fletch and one bareshaft method and its not as good for me as the single tune method. That  doesn't neccsarily mean that its really better; probably that I'm just more comfortable tuning this way because I've done the single arrow method for decades.

When I'm done I can shoot a perfect arrow up to 25 yards with no feathers.
Pope and Young Life Member
PBS Regular
Compton Bowhunters
Mississippi Bowhunters Hall of Fame

Mint

Thanks for responding, it looks like everyone looks at the flight as opposed to how it sticks in the target which makes sense to me. I'm going to use a lighted nock to tune since i will be hunting with them so that should make it easier to see what is happening.
The Constitution shall never be construed... to prevent the people of the United States who are peaceable citizens from keeping their own arms.

Samuel Adams

NYB Life Member
NRA Life Member

Rob DiStefano

Barebow arrow tuning ... not the be-all, end-all, but at the least some things to consider.
IAM ~ The only government I trust is my .45-70 Gov't.

Kirkll

Don't overlook the thickness of the strike plate for tuning, and the material used. Depending on your riser, and how far too, or past center it's cut. The strike plate material used can make a big difference on stiffer shafts. For example.... A Velcro strike plate is soft and has a bit of cushion, and a thin leather strike plate is harder and can allow more center shot using a stiffer shaft with less tip weight.

Food for thought...
Big Foot Bows
Traditional Archery
bigfootbows@gmail.com
http://bigfootbows.com/b/bows/

McDave

Quote from: Mint on December 09, 2025, 04:00:50 PMThanks for responding, it looks like everyone looks at the flight as opposed to how it sticks in the target which makes sense to me. I'm going to use a lighted nock to tune since i will be hunting with them so that should make it easier to see what is happening.

If you're shooting in daylight, you shouldn't need lighted nocks to see deviations in the arrow flight.  If your arrow is flying true, all you really see is a nock flying away from you, but as soon as you have nock left/right/high or low, you see a shaft flying in that direction, and it's really obvious.

You shouldn't have to make any particular effort to focus on it.  Continue to focus on the target and you'll see everything you need to see in your peripheral vision.
TGMM Family of the Bow

Technology....the knack of arranging the world so that we don't have to experience it.

Tajue17

I have to tune by flight because i use big broadheads and they can offset the point of impact on me if the arrow nock is badly kicking to one side,,, once i get straight flight at at least 15yds i then start over bareshafting but canting the bow at my normal stsnding shot and ususlly i have to lower string nock a smidge and raise the point weight...... but most friends just bare tune olympic style and go with that.   

Your form along with even tension on thise fingers is important,,, and if you are new one of those silent klydex draw checks black widow sells will eliminate so much mistakes,,, remove it after a year when your draw length and anchor are locked in solid!!!
"Us vs Them"

Flemish Twister

Quote from: Kirkll on December 09, 2025, 06:18:37 PMDon't overlook the thickness of the strike plate for tuning, and the material used. Depending on your riser, and how far too, or past center it's cut. The strike plate material used can make a big difference on stiffer shafts. For example.... A Velcro strike plate is soft and has a bit of cushion, and a thin leather strike plate is harder and can allow more center shot using a stiffer shaft with less tip weight.

Food for thought...
100% agree. I fought for a couple of hours shooting .204 ID carbons out of my long bow cut past center and flat out would not bare shaft tune for me.  Finally took a break and sat down to ruminate. Only thing I had not tried, so changed the strike plate thickness and it was like magic.  Lazers with Broadheads too
Oberon Recurve 60" 40#
October Mountain Carbon Z ILF Riser Das Long bow Limbs 62" 42#
Red Wing Hunter 58" 45#
1956 Bear Kodiak 64" 48#
Eagle X9 58" 40#
DIY Lam Long bow 64" 70++#

Stringwacker

Another 'one-off' with bareshaft tuning is while you can match the point weight you bareshafted with the same weighted broadhead....and get wonderful flight due to the straightening effect of feathers; the broadhead being longer effects dynamic spine making the shaft act weaker. A solid design broadhead weakens the dynamic spine more than a vented design. Kind of what Rob said, the bareshaft isn't the end all of the matter but it makes a straight shooting arrow. I my case the broadhead needs to be able 20 grains less than the field point most of the time.

Often the dynamic shaft weakening by the broadhead is largely offset by the addition of feathers on the back of the shaft...which stiffens the dynamic spine by nature of the 12 grains or so of additional weight which is mostly in the quill.

Sooooo...for the purpose of getting around the effects of the forementioned issues; I broadhead bareshaft tune after the finding the perfect bareshaft tune with field points. I do this by fletching the shaft and then cutting everything off but the quill and about 1/8" of feather. The broadhead tune imperfections show up quickly and then you make the same adjustments you did when using field points....only then do you have the perfect broadhead tune.

I do shoot the bow perfectly verticle to interpret correctly what I am seeing in flight when bareshaft tuning.

For those who have safety considerations it might not be worth taking the last step for tuning broadheads. In my case, I don't have a neighbor within a couple of miles in the direction I'm shooting. The 1/8" feathers is enough to steer the broadhead after field point tuning via bareshafting; but a bad release would miss your target; much like bareshafting field points.

No one needs to go the final step but I've done it for so many years its all second nature to me. Its just part of my normal tuning process.
Pope and Young Life Member
PBS Regular
Compton Bowhunters
Mississippi Bowhunters Hall of Fame

BAbassangler

Quote from: Tajue17 on Today at 05:52:37 AMI have to tune by flight because i use big broadheads and they can offset the point of impact on me if the arrow nock is badly kicking to one side,,, once i get straight flight at at least 15yds i then start over bareshafting but canting the bow at my normal stsnding shot and ususlly i have to lower string nock a smidge and raise the point weight...... but most friends just bare tune olympic style and go with that. 

Your form along with even tension on thise fingers is important,,, and if you are new one of those silent klydex draw checks black widow sells will eliminate so much mistakes,,, remove it after a year when your draw length and anchor are locked in solid!!!

Very interesting, I was confused as to what all is going on when my perfect Olympic style bareshaft flew wonky when canted in hunting stance.  So nock point micro tune, hmmm.  I get the extra point weight/shorter draw, but will have to think on this for a while.
I pity da'fool...that rejects Christ.

62" ILF, 40# Bosen recurve limbs on 19" Deerseeker riser
62" ILF, 45# Bosen longbow limbs on 17" Discovery riser
66" Kodiak Special 38#

BAbassangler

Quote from: Stringwacker on Today at 08:09:39 AM...In my case the broadhead needs to be able 20 grains less than the field point most of the time.

Often the dynamic shaft weakening by the broadhead is largely offset by the addition of feathers on the back of the shaft...which stiffens the dynamic spine by nature of the 12 grains or so...

Thanks for putting some numbers on it; makes it easier to see.  I shoot an elevated rest with AAE trad vanes or feathers, and have noticed a difference.
I pity da'fool...that rejects Christ.

62" ILF, 40# Bosen recurve limbs on 19" Deerseeker riser
62" ILF, 45# Bosen longbow limbs on 17" Discovery riser
66" Kodiak Special 38#


Contact Us | Trad Gang.com © | User Agreement
Copyright 2003 thru 2025 ~ Trad Gang.com ©