INFO: Trad Archery for Bowhunters



Author Topic: 4 point footing..start to finish..pic heavy  (Read 9554 times)

Online Tater

  • TGMM Member
  • Trad Bowhunter
  • ***
  • Posts: 2410
Re: 4 point footing..start to finish..pic heavy
« Reply #20 on: February 08, 2012, 07:48:00 AM »
Nice job on the footing..!
Compton Traditional Bowhunters Charter/Life Member
Big Thompson Bowhunters
United Bowhunters of Illinois
TGMM Family of the Bow

Offline lovethehunt

  • Trad Bowhunter
  • **
  • Posts: 174
Re: 4 point footing..start to finish..pic heavy
« Reply #21 on: February 08, 2012, 09:21:00 AM »
Thanks for the nice comments guys. Here are the answers to a few questions.

1. I used tite-bond glue, I had it right there on the bench. Any good wood glue should work as long as the shaft is sealed well after its done.

2. My jig block is 5 inches long with a 1/8 inch bevel. This yielded a 3 1/2 inch foot.

3. I saw the jig done on a post by Jason Westbrock and on another forum. It was not to difficult to make. Web search "Footing wood arrow shafts"

I also made a 10 inch taper tool that I will post later. Used a drill to turn the shaft, very effective.

Todd

Offline Troy Breeding

  • Trad Bowhunter
  • **
  • Posts: 330
Re: 4 point footing..start to finish..pic heavy
« Reply #22 on: February 08, 2012, 09:56:00 AM »
Todd,

I made dozens of footed shafts using about the same setup you are using.

Have you had any problem with the footing splitting as you push the two pieces together?

This was my biggest problem. I'd do my best to pick the straightes grain material for footings. Take extra care in getting as clean a joint as I could. Then crack,,, I'd hear a tiny pop or crack and see the footing split. Very aggervating...

Troy

Offline lovethehunt

  • Trad Bowhunter
  • **
  • Posts: 174
Re: 4 point footing..start to finish..pic heavy
« Reply #23 on: February 08, 2012, 10:02:00 AM »
Troy, I did have a little trouble with that. Make sure you clamp the foot before inserting the shaft. I am going to experiment with a wider kerf saw blade on the foot. I used a .020 on the first couple and bought a .025 to try. A longer taper may also help cut down on the steep angle of the wedge effect. If they do split fill  the area with ca glue, it's much stronger then the footing wood.

Todd

Offline Troy Breeding

  • Trad Bowhunter
  • **
  • Posts: 330
Re: 4 point footing..start to finish..pic heavy
« Reply #24 on: February 08, 2012, 10:06:00 AM »
Todd, that was going to be my suggestion to you. I had to clamp the footings at the end of the cut to stop it.

The problem with longer fingers on the footing is getting them all to come out at the same point on the shaft.

Using a wider curf blade really helped.

Troy

Offline wixwood

  • Trad Bowhunter
  • **
  • Posts: 109
Re: 4 point footing..start to finish..pic heavy
« Reply #25 on: February 08, 2012, 11:00:00 AM »
I love the do it yourselfers that post on this site. I AM going to build some footed shafts one of these days.

Thanks,     sw
Fort Collins Archery Association
Colorado Traditional Archers Society
Colorado Bowhunters Association
NRA Life Member

Offline Troy Breeding

  • Trad Bowhunter
  • **
  • Posts: 330
Re: 4 point footing..start to finish..pic heavy
« Reply #26 on: February 08, 2012, 11:33:00 AM »
wixwood,

Be careful, very careful,,, It's habit forming!!

Troy

Offline Mike Vines

  • Trad Bowhunter
  • **
  • Posts: 4512
Re: 4 point footing..start to finish..pic heavy
« Reply #27 on: February 08, 2012, 11:44:00 AM »
Quote
Originally posted by Troy Breeding:
wixwood,

Be careful, very careful,,, It's habit forming!!

Troy
VERY HABIT FORMING.
Professional Bowhunters Society Regular Member

U.S. ARMY Military Police

Michigan Longbow Association Life Member/Past President

Offline tecum-tha

  • Trad Bowhunter
  • **
  • Posts: 613
Re: 4 point footing..start to finish..pic heavy
« Reply #28 on: February 08, 2012, 11:52:00 AM »
4 wing footings look beautiful, but hardly really add considerable impact strength to the arrow. It takes a long time, is messy and cumbersome. Especially the reduction of the 4-wings into the arrow diameter.
The conical splice, which the arrow-fix or the rep-arrows are using are much better for impact strength. I was shooting 1/2 doz. 4 wing footed cedar shafts footed with Jatoba (in the ironwood family)into a concrete landscape block. All 6 splintered and shattered along the arrow shaft and made the shaft completely unusable/unrepairable. After that test, I shot a single cedar arrow, footed with 1.5" of black locust wood behind the point using the arrow-fix conical splice method. I was shooting the arrow 7 times. After the 7th impact, the field tip split along the ferrule. The arrow is still fine. Distance for all shots was about 11 yards and with a 60# longbow. Assuming, that the little footed arrow would have broken off, the break would have been right behind the point and could have been easily repaired again. I have 1 arrow out of my 3D-shoot set, which is repaired 5 times within the first 4" behind the point. Works fine. I am currently evaluating hickory and ash....which can be bought in arrow shaft diameters...

Users currently browsing this topic:

0 Members and 1 Guest are viewing this topic.
 

Contact Us | Trad Gang.com © | User Agreement

Copyright 2003 thru 2024 ~ Trad Gang.com ©