Hey guys.... Give me your best tips for making adjustments to allow the arrow to go where you're looking. Let's say the arrow bare shaft tests perfect (correct spine) BUT hits the target just slightly to the left of where you're looking...what would you do to get the arrow to "move" slightly to the right in this situation ? Please advise in detail... Thanks
I'm right handed and when I'm hitting left it's form. Not getting into my back. When I get arm back and use my back muscles it puts me back on center. Form first befor adjusting the bow set up.
If you are right handed also check anchor point. short drawing the bow slightly can also cause a left hit.
I shoot left handed so I'll give you my take when I am hitting to the right of where I am looking and I know my arrows are tuned. Like Mr. Armstrong said--form. Issues could be that I've moved my hand further out (inadvertent change in anchor) or don't have my head canted like usual (eye not over the arrow). But if these types of things don't work and you are wanting to change impact through sideplate I would say that your left hits would signal slightly weak arrow so you could build out sideplate so bow would accept the slightly weak arrow (pardon my terminology--Im sure this could be better stated) and get it to impact more to right. You could also try cock feather in and see what happens. Just some ideas...But back to the beginning---rule out any form issues first.
I'd put a couple twist on my string and leave side plate alone.
2nd that raise your brace hight a little until your where you want.
Let's assume your form is perfect and the arrow still hits a little to the left, and you're a RH shooter. By softening the side plate you can move the POI a few inches to the right at 20 yards. In other words, if your side plate is plain leather, you can peel that off and put Velcro on instead. If your side plate is Velcro, you can peel that off and put a rug rest on instead, such as a Martin rug rest.
No bow is the same as any other bow, and it is convenient to be able to move the POI so it impacts the same as other bows you're used to. Of course, if you move from a contoured grip recurve cut past center to a broom handle longbow cut to center, you're just going to have to learn a new way of shooting. But in moving from one bow to a similar bow, it is helpful to make small adjustments so both impact in the same place.
Everybody above is also right, of course. Once I learned how to actually come to full draw, my arrows suddenly started impacting right, and I was replacing my Martin rug rests with Velcro to go the other direction.
If he's right handed and hitting to the left, that would indicate a slightly stiff arrow. I'd put on a heavier point first, before I started doing a lot of sideplate changes.
http://tradgeeks.com/how-to-bare-shaft-tune-arrows/
Watch the short bare shaft tuning video :readit: why with the video proof :archer2:
Sorry I should have said left hits signal stiff arrow for right handed. Guess if I'm going to comment in future I need to learn my lefts from rights. I would have to shoot left handed just to make things more difficult for me
I don't believe he is "building out" the side plate in the video as much as softening it to let the arrow bounce less off the sideplate. If you build it out, meaning to make it thicker, without making it softer, it will have the opposite effect, I think and the arrow will strike even farther to the left.
QuoteOriginally posted by Tradcat:
Hey guys.... Give me your best tips for making adjustments to allow the arrow to go where you're looking. Let's say the arrow bare shaft tests perfect (correct spine) BUT hits the target just slightly to the left of where you're looking...what would you do to get the arrow to "move" slightly to the right in this situation ? Please advise in detail... Thanks
By all means. Move it to the right a fuzz..... if you have room to to it, it should work fine. It wont take much though... If you go too much it will effect your spine.
Hmmmmm. If the arrows hit left of where you're looking, they're not bare shafting perfectly. Bare shafting is indicating the arrows are stiff, for a right handed shooter.
Just add a little point weight and you should be good to go. Thinning the side plate will do the same thing, but easier to add point weight.
Of course, you could be looking across rather than over your arrow. A slight turn of the head more toward the target should correct that. Good luck.