At 54 this is getting tuff to do by myself. went this morning to refine a spot I have been hunting and seeing a lot of bucks, screw in steps liked to kill me, then pulling up that 25 lb stand and trying to get it hung took dang near an hour and I was worn out when I finished. I can remember when this was a fifteen minute job tops and would do 3-5 a morning. Whew :banghead:
Look at treehopper bolt system. I can put steps in a tree in less than 10 mins with a cordless drill and their bolts. I also have been using the muddy vantage stand and their brackets. Stand is light and with multiple brackets i just take stand with me and use it all over. Both products have cut tree stand set up time in half for me.
QuoteOriginally posted by shedhunta:
Look at treehopper bolt system. I can put steps in a tree in less than 10 mins with a cordless drill and their bolts. I also have been using the muddy vantage stand and their brackets. Stand is light and with multiple brackets i just take stand with me and use it all over. Both products have cut tree stand set up time in half for me.
Gary, what power cordless drill does it take for the bolts...and is it very heavy to pack in?
I got the treehopper hand drill and a bit for it and cordless...but I'm getting too old to hand drill them.
keith. I hear you buddy, I'm 62 and still hanging stands and loving it. it just takes a little longer.... Tell you what, hauling a screaming eagle 1 1/2 miles at 10,600 feet to my secrete hot spot is a grunt.
Joe
Screw in steps can wear you out fast at any age.
If you want to set multiple areas and leave them up maybe the 39 dollar steel 16 foot sticks would be easier. I used to use screw in steps and they require a lot of energy to install by hand.
I got a 12volt compact lithium Bosch on clearance at Lowes w/2 batteries & charger for $70- charges in 30 minutes.
Bought a 6-pc Stubby Auger Bit Set by "Drill Master" from Harbor Freight for $9.00, which includes the 3/8-inch auger bit.
From a local fastener supplier, I ordered 50 Grade-8 Hex (Allen) head 3/8"Diam x 6"L (corrected) black bolts for about $1.00 each.
One fresh battery will drill about 12 to 16 3/8-inch diameter x 3-inch deep holes for about 3 stands. I drill at a slight angle down so when you place your weight on them, they're never less than level - and the bolt threads dig in too.
Carry only the bolts I need with the drill in a fanny pack or a military mag pouch.
I can sure relate to this!
Keith I hear you and hate screw in steps. I got a Loc On Windwalker and its light and easy to hang.
Coil that sounds like the trick. I'm going to try it.
LB hntr, I have used climbing sticks only for about the last 10 years, now I remember why :saywhat: Usually use API aluminum. No more great deals for me.
http://www.sportsmansguide.com/net/cb/guide-gear-climbing-stick-and-tree-stand-combo.aspx?a=552579
I use several of these set ups on my property. Quick and easy. My 70 year old father much rather use this set up verses the screw in tree pegs.
Correction to my above.. 6-inch bolts (six) not eight, but use GRADE -EIGHT yes 8 strength, so they won't bend. I don't drill in pines, live hardwoods only, and drill 2.5"-3" deep leaving 3.5" for my hand or step.
Stiff soled boots help when drilling, too, for the smaller diameter bolts. You could use 1/2" diam. bolts, just harder and slower on the drill and battery. Try both and see what's best for you.
LW sticks! 15 yrs here. Set up and take down every time. Takes 10 minutes. . . 53 and have an inner ear vertigo disease.
I have been getting away from the steps the last few years. Been changing out to climbing sticks. Just need to find something to do with the 5 gallon bucket of screw in steps now.
I've been picking up rails and sticks the past few years. I finally have enough to work up a half-dozen stands. I still might use screw in steps the first 3-4, that I can reach from the ground and then go to the rails.
Few things more exciting than setting up on a new stand! A good way to relive opening morning multiple times per season!
I want to add that my dad has a homemade bracket with a pullie that he mounts to a climbing stick so he has a easy pull up of the stand. He pulls up the stand to whatever elevation he wants, ties it off to the ladder, then he climbs up and attaches the stand to the tree without any issues of trying to hold up the stand and mount it at the same time. Makes a world of difference.
Get a climber.
QuoteOriginally posted by Hoyt:
QuoteOriginally posted by shedhunta:
Look at treehopper bolt system. I can put steps in a tree in less than 10 mins with a cordless drill and their bolts. I also have been using the muddy vantage stand and their brackets. Stand is light and with multiple brackets i just take stand with me and use it all over. Both products have cut tree stand set up time in half for me.
Gary, what power cordless drill does it take for the bolts...and is it very heavy to pack in?
I got the treehopper hand drill and a bit for it and cordless...but I'm getting too old to hand drill them. [/b]
I use a makita 18v lithium and can drill 3-4 set ups with one battery. May look into one if the small compact lithium drills just for times when I am hanging and hunting in the same day. Having a belt clip on the drill is a big help.
I either use sticks or better yet...ladder stands.
Faster, safer, comfortable, easy to set.
Of course if it isn't your land, you may have to use hang-ons, but then I would use the climbing sticks. Why damage the tree, by drilling or the use of screw-in steps? If you forget to remove just one screw-in, you are going to ruin some loggers day,eventually.
I also remember a friend of mine slipping while climbing. He didn't fall, but speared himself with a step thru his lung. bled like mad and almost died.
I wouldn't use screw-ins or bolts nowdays...thing of the past. too many negatives.
You might be tougher than I am, so suit yourself.
Just my opinion.
Although Chippewa wedge lock is no longer building treestands (he retired), the system they used allowed one to install a lightweight "holder" system, then just place the treestand into the system. WAY easier than messing with installing a traditional treestand.
I noticed that Big Jim has some stand systems that have a relatively similar feature. Check those out. I agree with those that like the strap on climbing poles. Yeah they are tall, and unwieldy, but once in place, they are there and pretty sturdy.
Later
ChuckC
The last stand I put up, I used my viper climber. Started from the top by climbing, then pulling my hang-on up. As I descended, I screwed in the steps from top to bottom. Worked better than trying to hang on to the tree and screwing them in as I go.
When you do it bottom to top, the easy ones are at the bottom, and you get tired in the most dangerous position. Be safe.
Second the Tree Hopper System. I highly recommend his stuff and for the price you can't go wrong. I see him every year at the Sportsmans Show is Harrisburgh Pa and buy another bag of steps for good measure. I have started hiding them near my stand location so I don't have to lug them in each time.
Cranford deluxe tree steps screw in very easy.
I hunt my own property so mainly use ladder stands. In the more remote corners of it I use a climber but am considering switching to climbing sticks.
Screw ins are not even a consideration. I typically hunt alone & with all the horror stories of them refuse to even risk it.