HI guys,I currently own two Assenheimer master hunters and a 3 piece 62" A&H ACS.I like my bows and taken some nice deer with them.I have owned a 56" caribow tundra wolf and a 56" JK Kanati.Plenty of deer in VA. but not many bowers,to test their bows.My question is where does a Toelke Whip stand among these bows?
ML,
I don't have any experience with the bows you mentioned, but I bought a Whip off a member here about a month ago. It's as smooth as any, quieter than most, and no slouch in the speed department. Hand shock is practically nonexistent.
Ken
Thanks Ken ,was thinking about trying one out.Bow sure does get alott of good feedback!
I have only shot a few and only one in the last year. It was nice, had good speed and was quiet for sure. Little thump in the shot. Liked the grip a lot. Nice looking.
Of the bows you listed, I have shot only two of them very much. Those would be the Kanati and the ACS. The whip has noting over either in shooting quality as far as I am concerned. Maybe a whip is a hair more quiet, but hard to say without being able to tune each to maximum potential. I will say the whips in general are prettier than the average Kanati or ACS, but that is subjective as is the grip on the three bows. The Kanati bows I have shot were fast, smooth, quiet and about dead in the hand given the weight of them. I would say the Kanati is a better short bow if matched to the others at the same length for all. The ACS I had with the heavier riser weight was one of the smoothest, fastest and deadest in the hand hybrids I have ever shot.
Honestly, I am watching for the right length and weight in all three to show up in the classifieds.
I have owned an A&H three piece, I personally prefer the whip over the A&H, I feel that the whip has a much more stable limb. Also, Toelke bows are built to a plus or minus -/+ .5 lbs draw weight, almost never take longer then 3 weeks to build a bow, spray the limbs with something like 6 or 8 coats of epoxy and the riser with even coupe more coats, have the best customer service that I have found. And, also have a ton of shooting knowledge. Needless to say, I am a huge Toelke fan, all of the bows that I own are Toelke.
X2 on Toelke. I could not have said it better than Tutanka.
If you think the Whip is nice, you should also try the Lynx.
I agree with Rick, if you like a 3 piece the Lynx really is something else.
A whip will probably be much lighter in mass weight then the others. I don't have anything bad to say about whips. I would tweak the grip an add a bit more palm swell if I was ordering one new, but that's just a personal thing.
I just bought a whip from Dan and I'm very happy with it. I am new to archery, so I don't have much experience with other bows, but I can tell you that there is nothing about my whip that I don't like. Plus, as others have mentioned, Dan's customer service is great. I called him just before Christmas to see if I could demo a bow. He said sure, but I don't have anything in stock that matches what you're looking for, so why don't I just make you the bow you want and if you don't like it, send it back. He told me that he would ship the bow out the first week in January, and that's exactly what he did.
NittanyRider,
That is exactly what Dan did with me on the two bows I purchased from him. Dan is so confident in knowing if he gets the bow into your hand, then there will be no sending it back.
Just by a simple one time conversation in most cases, Dan can build what you can't necessarily put in words decribing what you are looking for. Hence, awesome bow...thus no return.
H
I just bought a 62" Whip HS from Rick and I have to agree the finish is well above the level on most of my other bows. They don't get any quieter and I've had quite a few r/d longbows.
My only complaint, and the reason mine is back up for sale, is that it starts stacking badly when drawn 29" and I draw a bit more than that. My 60" Lost Creek Life Ender handled my long draw with no problem and my 62" Judge will come back behind my ear without bottoming out. If I were to get another Whip, it would have to be a 64" or maybe 66" and if I go that long, I'd rather shoot a "D" type bow. For someone with a 28" or shorter draw, I'd say the 62" Whip HS is quite a bow.
I recently purchased a used 64" Whip from the classifieds and couldn't be happier with it. I've always shot recurves and didn't necessarily like longbows... the few that I had shot. The Whip is smooth, fast and I shoot it better than I ever shot a recurve.
QuoteOriginally posted by threeunder:
ML,
I don't have any experience with the bows you mentioned, but I bought a Whip off a member here about a month ago. It's as smooth as any, quieter than most, and no slouch in the speed department. Hand shock is practically nonexistent.
Ken
x2
QuoteOriginally posted by Bladepeek:
My only complaint, and the reason mine is back up for sale, is that it starts stacking badly when drawn 29" and I draw a bit more than that.
Bladepeek. You may want to give Dan a call and ask him about it. I have a 32" draw and the Whip I have(admittedly not HS) doesn't stack at all. It does gain the standard 3lb per inch.
may very well be an "HS" thing.
has to be a trade off somewhere.....
curious as to what you find out.
I'll go try to draw an extra couple inches on mine in a bit...
with my 62" HS I can feel it start stacking at about 30"
at 31.5-32" she's quickly getting pretty stiff.
What's the brace on yours Bladepeek?
..maybe..the string is a little short..?
Interesting... I know that Dan has a very good reason for anything he does. Must have been a pretty good increase in speed for him to change his design that much.
My experience with a bunch of whips mirrors the above, it always felt like his 62" bows stacked about 28". Pre HS mind you. My personal feeling is add 2" to whatever length Dan tells you, have also heard the same from many others. Please don't take that as a slight, great bows and the best bowyer in the business, Dan just seems to like his bows shorter then I.
Maybe I'm a nutter then. I absolutely love my 62" Whip and I draw it 32". Never noticed a stack, just a smooth continual increase in weight.
Interesting. I spoke to Dan about this very thing and went specifically with the 62" HS. i draw 29" with no issues.
I haven't talked with Dan, as I didn't buy the bow from him. Just looking at the fades, the riser is WAY longer than my other r/d longbows, which leaves a lot less working limb. I don't see it as a Whip HS problem, but as a "didn't do my homework" problem. I'm sure Dan would have recommended a different length bow. It certainly wasn't the seller's fault either. I'm sure he would have tried it at a longer draw if I'd asked him to. It's great back to 28" and a little bit more. I just fell all over it when I saw it in the classifieds and didn't know enough to ask the right question.
Complete shot in the dark, but I wonder if Dan built it differently on purpose.
This is my new 62" HS Whip....do the riser/fades look about the same? Just curious is all. Here are few angles to check out.
(https://lh4.googleusercontent.com/-MTCA3EGFZGE/UNDcE5wg0rI/AAAAAAAADhQ/ubIr_MFyqV8/s800/IMG_1005.JPG)
(https://lh6.googleusercontent.com/-LOc_Jaes9K4/UNDcD3JClII/AAAAAAAADg8/jvhBC2SNecE/s800/IMG_1000.JPG)
(https://lh4.googleusercontent.com/-Rp4Hs_FjyhM/UNDcEOgjUII/AAAAAAAADhE/9BVi2NBUFn4/s800/IMG_1001.JPG)
(https://lh5.googleusercontent.com/-fQNWEd2CSj4/UNDcEhOqZYI/AAAAAAAADhI/Riy2C5yW8D0/s800/IMG_1002.JPG)
Off topic here but....TxAg. That is a stunning Toelke right there. I have always thought mine to be the prettiest I've seen Dan build but yours rivals it!
Yeah TxAg, that is one fine longbow.
I have a pre-HS Whip thats 62" and don't feel it stacking at my 29" draw.
Txag..
PRETTY is an understatement.
Also, I've wondered the same thing about "on purpose"
Wouldn't surprise me a bit.
OK guys, I am now so confused that I don't have a clue what I'm talking about. I drew the bow when I first got it with no arrow on and said "Ouch, this thing really starts stacking at my draw". I took it to our neighborhood indoor range and shot it with an arrow drawn to my usual "middle finger on corner of mouth" anchor. Same impression. I was swapping bows back and forth with another shooter who has a 29" draw (I draw 29.5"). I shot his new bow and he shot my Whip HS. First words out of his mouth were "This thing really starts stacking right about here". I looked at the pics of TxAg's bow above and then measured my riser. To the ends of the fades, it's 21". Most of my other r/d longbows have been around 17.
So, having convinced myself that it was in fact an extra long riser with short working limbs that were stacking badly, I put it on a scale and plotted it out from 26" to 30". From 27.5" to 29.5" the line graph is a damned near perfectly straight line - 37# @ 26"; 46.5# @ 29.5 with plotting points every 1/2". I think my scale is pretty accurate, but it is definitely very consistent. I weighed it 3 times at 1/2" draw increments and the graph just couldn't be any straighter. Subjectively, when I hit 29.5" in a regular draw, I have the feeling I couldn't draw it another 1/2" without it turning into a 2x4. Put it on the scale and pull it down with both hands and I get this nice, linear draw curve. From 29" to 29.5" it gains 1.7 lbs. From 29.5" to 30" it gains 3 lbs so I would have to say it starts stacking at 29", but my impression when shooting it is that it starts a bit before that.
I'm a retarded - I mean retired engineer and I have confidence in the measurements I just made, but subjectively, I think the bow needs to go to someone with a bit shorter draw.
signed,
Confused in Michigan
I draw 29.5 and mine is a 62" whip. I do not notice anything. Seems pretty comfortable to me.
Perhaps the bow was built for someone with a considerably shorter draw length. I have owned 7 Whips, 6 of them have been 62", I draw a full 29" and none of mine ever had a hint of stack.
Jim may have a point. I know Dan made mine specifically for my short draw. I have a 62" Super D that starts to stack at 29".
Dan specifically built it for me.
The last one I shot was 62 and I didn't notice anything at 29" shooting it. I also over drew it at least another 1/2" and it was smooth.
Well, the bow is sold (or will be this evening when the auction closes). I won't really miss it since the two of us never really clicked. On the other hand, the bow was so beautifully built and finished and the grip just perfect. I think I will contact Dan and ask him if that bow was built specifically for maximum performance at a short draw.
Way too many shooters telling me their 62" Whip HS draws fine at 29" -30" to ignore. Whoever gets this one this evening will get a beautiful bow that is very quick for the draw weight and if he draws less than 29" will think it is the sweetest bow he ever shot.
I think my post sort of hijacked the original post and I apologize to mec lineman. I do appreciate all the info it generated, though, and I would say all the positive responses should have answered his original question pretty thoroughly :)
Please dont apologize,I found it all imformative.I dont make many post due to computer time.I was happy to see so much imput.This is what I have gathered they are some loyal whip folks out there.Everybody says the same thing " sweet shooting QUIET beautiful well made bow" I will keeping my eye out for one in the classifieds with the right specs!
QuoteOriginally posted by Bladepeek:
Well, the bow is sold (or will be this evening when the auction closes). I won't really miss it since the two of us never really clicked. On the other hand, the bow was so beautifully built and finished and the grip just perfect. I think I will contact Dan and ask him if that bow was built specifically for maximum performance at a short draw.
Way too many shooters telling me their 62" Whip HS draws fine at 29" -30" to ignore. Whoever gets this one this evening will get a beautiful bow that is very quick for the draw weight and if he draws less than 29" will think it is the sweetest bow he ever shot.
I think my post sort of hijacked the original post and I apologize to mec lineman. I do appreciate all the info it generated, though, and I would say all the positive responses should have answered his original question pretty thoroughly :)
I'm glad you posted. It was informative. I learn something new here every day.
In my 20 years of shooting and hunting with longbows and recurves I have shot and owned many and in my opinion Toelke ranks among my top five. I am happy to own a Whip,cannot beat the craftsmanship or performance . There must be something in the water up there in Montana LOL. Don
Well, it turns out we are all right.
1. Dan Toelke makes some really great bows.
2. His workmanship is of the finest order.
3. Lots of guys with long draws are very happy with their Whips.
4. I had the wrong Whip. Mine had a 21" riser. Below is Dan's response to my question asking whether I had a bow made for a shorter draw.
"Ron a HS 62" for a 29 1/2 draw would have a 18 3/4 riser, a 21" riser would be best for a 28"draw or less, a short draw archer in my book is less than 27" Dan"
Bottom line, if I stumble across another Whip for sale in the poundage I like, I would hesitate only long enough to ask the length of the riser. The quality of the bow is already established.
Ron
Bladepeek, you mentioned the grip on the bow being "just perfect". Do you know if it was a custom grip, or the standard grip on Dan's bows? Just curious.
QuoteOriginally posted by Bladepeek:
I just bought a 62" Whip HS from Rick and I have to agree the finish is well above the level on most of my other bows. They don't get any quieter and I've had quite a few r/d longbows.
My only complaint, and the reason mine is back up for sale, is that it starts stacking badly when drawn 29" and I draw a bit more than that. My 60" Lost Creek Life Ender handled my long draw with no problem and my 62" Judge will come back behind my ear without bottoming out. If I were to get another Whip, it would have to be a 64" or maybe 66" and if I go that long, I'd rather shoot a "D" type bow. For someone with a 28" or shorter draw, I'd say the 62" Whip HS is quite a bow.
Interesting I have never has that issue. My 58 is smooth out to my draw length which runs about 28.5.
the bowyer customizes the bow to your draw length.
Glad I kept up with this thread. I didn't know about the two riser lengths.
Anyone know the recommended max draw on she 18 3/4" riser 60 & 62"?
extrema312 read Dan's own recommendation in quotes in my post above about the 62". Can't help you with the 60".
GrayRhino, I believe, just looking at my grip (actually not mine any more) and the pictures of other Whips I would say it was a standard grip. I don't like a really fat grip or one too high. This Whip felt perfect.
I get the feeling from other's posts and from Dan's message that he is pretty capable of making the bow to fit any of us if he gets the right input. I sure would talk with him if I was in a position to buy a new bow and make sure he knows my likes and dislikes.
Ron
This is just my opinion, but wrt R/D bows for 27-28" draw 64" is best, for 29-30 a 66" is best, 31-32 68". Add 4" for a straight limb bow. IMHO most folks are ording bows far too short. Look at the bow lengths in the classifieds! The short ones are for sale!