I have a Thunderhorn Boa quiver, and im trying to figure out how to get all 6 arrows in the hood portion of it and still have fletching clearance! Pictures, or any ideas welcome!!!
Are you using 2 or 3 blade heads? 2 blades are easier if you alternate the broadheads high and low in the quiver. That way the fletching is not touching.
i remove one of the arrow clips and just put 5 arrows in,three blades are kinda tight,but i shoot two blades.
Usually only carry 3 snuffers when using a bow quiver......
I do like Arrow30 recomends. I take one or two of the clips off, they just slide out.
Zig-zagging the heads in the hood helps too.
OkKeith
If you haven't already, slide/strap each section of the quiver as far up on the fade outs as you can. The closer the two parts of the quiver are together, the further they spread the fletching.
I have a new hood foam for it that i plan on filling for elk hunting with WW! The one i have installed now is a 5 hole for deer, small game, etc., usually never a problem when hunting locally, but dont wanna take a chance elk hunting! Seems to me that Tred Barta has his quiver plum full, using the same high backed fletching i use and the same broadhead i plan on using...How?
Travis,
I guess so it looks good on TV...
If I am stand hunting or blind hunting I always take the quiver off the bow. If the quiver is crammed full and the fletching touches each other, they buzz like crazy when I shoot. Not to mention it will eventualy bugger the feathers.
Like I said, I only carry 4 or 5 arrows. I have a hard time thinking of a scenario where I would need more than that at one time while deer hunting. If for some reason I was to totally "de-quiver", I always have more in the truck.
Space them out, put fewer in; I think you will be happy.
OkKeith
QuoteOriginally posted by arrow30:
i remove one of the arrow clips and just put 5 arrows in,three blades are kinda tight,but i shoot two blades.
I do the same thing. I noticed I couldn't get 6 in my quiver as well. And I use a 2 blade head.
Most of us place the heads in the hood more or less side by side alternating back and forth. I had the same problem with the Boa so I tried a different approach.
I found this works for 2 blade heads and field points. Not sure how it would work with 3 or 4 blades. It is simple to do but hard to describe so I'll try it this way. Lay the bow on it's side, quiver up. Start with the second arrow. Place the second 2 blade head parallel to the ground, at the middle of the hood and towards the front of the hood, that is the side of the hood that is farthest from the bow. Place the third head at the middle of the hood and immediately under the second head. Finally place the fourth head at the middle of the hood immediately under the third head. The three heads should be stacked vertically. Now place the first arrow and the fifth and sixth arrow where convenient.
This gives a lot more spacing of the fletching for me. Hope it works for you.
JW
I use 5-arrow quivers but put only 4 arrows in. I put three broadheads on one side, rotated so the feathers don't touch. Then I put a judo or field-tipped arrow on the other side. I leave one arrow position empty between the target and hunting arrows. In the rare instance that I might need more than 3 shots at game I've been known to take a spare broadhead or two in my pack. With these I can retrieve an errant arrow (assuming I can find it) and reload the arrow.
Only one time in more than 40 years of bowhunting have I needed more than 3 broadeads. That time, on a bear hunt, I needed 5. My first arrow was a miss, my second was a rear spine, and ....things got a little hairy but the bear went home with me.
(http://i756.photobucket.com/albums/xx210/mikemidd/Mobile%20Uploads/100MEDIA_IMAG0089.jpg)
(http://i756.photobucket.com/albums/xx210/mikemidd/Mobile%20Uploads/100MEDIA_IMAG0090.jpg)