Trad Gang
Main Boards => PowWow => Topic started by: BillyBobHowdieVern on March 20, 2006, 09:48:00 PM
-
is the vid here on sharpening WW good for snuffers also. i know this is a bonehead ? but i just got my snuffers and i have only had 2 blades till now.
thanks
john
-
Same technic just need that large 16" mill bastard file if you do it like Charlie. We were all using Bob Morrison's file at the Texas Sweat to get our WW & Snuffers sharpened. Very easy and scary sharp. I've always been a 2 blade shooter but those WW blew some nice holes in the javies & hogs. I think I'm converted..Jeff
-
Where is the vid for sharpening WW's? I just purchased snuffers and need to get them sharp soon for a Nebraska Gobbler or two.
-
thanks i kinda figuered it would be the same just wanted a confirmation. tombow the vid is in the members video's under sharpening WW
john
-
I'm with Jeff. Used to be a two blade man too, but the WW makes a nice hole, it's really easy to sharpen and it flies well too.
-
Snuffer Tamer kit.Sold at Three rivers.I saw one on the women-outdoors website 4 sale
-
--------------------------------------------------------------------------------
I use a 10 mil on my 160 gr Snuffers. Sharpen rear to front covering 2 blades, apply pressure.
I give each side 25 strokes then finish off the head on my Ceramic Crok Stik. Razor sharp edge that will shave hair.
-
where does everyone get there files from?
-
i just bought a big 16" file today from a local hardware, lumber store i ask them for one and they went out back in a shed and found one. sold it to me for $10.00 so i got a good deal plus it was the only big file i could find.
john
-
Yup, I do as Joe Skipp - extremely sharp every time.
Lay the file down on the bench with the tail facing you - then just draw the BH heel first towards you. Finish on crocks or super fine DMT stone.
-
I'll either shoot them right after filing or a couple of strokes on 600 wet/dry sand paper to polish.
-
I've managed to learn to sharpen them with 6" & 8" grobet files from 3Rivers. Of the two, the 8" being a little easier to get a better edge. However, if I was sharpening them at home or in the field in circumstances where a large file was handy, like back at the truck or some major camp site, I'd definitely use the bigger files on a sturdy table or bench.
But for carrying around all day in the field or on extended back-packing type affairs the smaller files are much easier to deal with and plenty adequate once you get the knack for using them.
I'm with the others though, the 3 blade heads lend themselves very well to file sharpening. - eric
-
Here's how we do it:
With the broadhead perpendicular to the rotation of the wheel (6 inch grinder, medium grit wheel) draw it from back to front, applying light/medium pressure on the head. Be careful to keep the 2 blades that are touching the wheel even (don’t “rock” the head up and down) and do not go down off the tip and blunt it. Also be careful not to overheat the head (will remove temper), I keep a bucket of water handy. You don’t want to develop any blue color on the blades-it takes quite a bit of heat to hurt them, though.
(http://img.photobucket.com/albums/v195/RyanRothhaar/grind1.jpg)
You are finished when you have a completely new, even cutting edge along the full length of the head.
These are really sharp enough to use now, they will not shave, but have a “burr” edge. I generally prefer a shaving edge and go on to the next step.
(http://img.photobucket.com/albums/v195/RyanRothhaar/grind2.jpg)
Using a hard black Arkansas (or any other hard oilstone) place the head with 2 blades flat on the stone and move in a circular motion with medium pressure. You will feel the metal coming off at first and after 10-15 circles it will start sliding like ice. This step is finished when it slides slickly.
(http://img.photobucket.com/albums/v195/RyanRothhaar/stone.jpg)
To achieve the final nasty sharp edge draw the head backwards on a piece of hard, smooth leather 6-8 times per side (2-blades flat on the leather). Some guys put fine jeweler’s polish on the strop, but I just use the leather. Put Vaseline or some other oil on the cutting edges to avoid rusting and you are ready to go. I occasionally strop the head a bit during the season to touch it up. This full process will only take a couple of minutes per head once you have the grinding step practiced up.
(http://img.photobucket.com/albums/v195/RyanRothhaar/Strop.jpg)
I hope this helps!
For extended trips, or hunts where I expect alot of shooting I take a Razor Rake pull through sharpener and a file, but for pre-sharpened heads the above process is the easiest and best we've ever found.
Ryan
-
This may be a stupid question, but would an 8" grinder work just as well? That is what I have, dont really want to buy a new one!
brackshooter
-
ttt for JC
-
I have been shooting my snuffers with the burr edge and have been pleasantly suprised.Not shaving sharp but provide major bleeding and pass throughs on whitetails.Ive been using a half round file.Anyone else leave em with the burr edge?
-
Thanks SteveO!
-
I will have to try this. Been looking around (locally even online) and the 16inch file is hard to come by.
Thanks for resurrecting this one... just in time for spring gobbler stalkin'.
-
John,
Bought my Nicholson 16" mill bastard file at Lowes. I would bet that HD would have them too.
nocams
-
I ordered mine from W.W. Grainger
www.Grainger.com (http://www.Grainger.com)
-
Big R has Big Files
-
ttt
-
I posted some pics on 2blade is having 3blade problems thread about using a file if you wanna check it out.