Post by: tippit on October 23, 2008, 11:45:00 AM
What is paracord:
"Parachute cord (also paracord or 550 cord) is a lightweight nylon kernmantle rope originally used in the suspension lines of US parachutes during World War II. Once in the field, paratroopers found this cord useful for many other tasks. It is now used as a general purpose utility cord by both military personnel and civilians. This versatile cord was even used by astronauts during STS-82, the second Space Shuttle mission to repair the Hubble Space Telescope.
The braided sheath has a high number of interwoven strands for its size, giving it a relatively smooth texture. The all nylon construction makes paracord fairly elastic; depending on the application this can be either an asset or a liability."
There are seven inner nylon strands. These can be left in place or pulled out. Other cordage can be used too ie. climbing rope, shoelaces, etc. Even larger diameter cord will work if you remove the inner strands.
(http://img.photobucket.com/albums/v110/tippit/Knives/Para-cordWrap023.jpg)
The bottom two cords are true 550 paracord.
(http://img.photobucket.com/albums/v110/tippit/Knives/Para-cordWrap003-1.jpg)
The inner nylon can easily be pulled out to make a thin flat cord or sealed in.
(http://img.photobucket.com/albums/v110/tippit/Knives/Para-cordWrap043.jpg)
When you heat seal the end, you want to make the tip more pointed so it will go through the hole in your knife handle easier.
(http://img.photobucket.com/albums/v110/tippit/Knives/Para-cordWrap004.jpg)
OK, Here's what you need to get started:
1) Length of paracord usually 6-10 feet.
2) Knife with holes drilled in handle. I use 1/4 drill bit. You can always put any kind of hard handle on later by just drilling your pining holes smaller through the handle material and through the larger 1/4 inch hole as the epoxy will hold everything tight.
3) Water to soak the paracord...remember the description of paracord being stretchy? Well by wetting and squeezing the water out of the cord, it seems to pull tighter with less spring back...therefore a handle that won't loosen up after use.
4) Needle nose pliers if you are having to pull the ends through the hole on the end. Nothing worse than getting done with the wrap and not being able to push the loose ends through the hole. If you let go of the wrap looking for the pliers, the entire wrap unwinds :knothead:
5) Thin piece of wood to push the wraps down and tight as you wrap. Seems like a nice piece of Osage make it more Traditional :)
Go get your materials as I'm going to my tree stand...Doc
Post by: ber643 on October 23, 2008, 11:57:00 AM
Post by: robtattoo on October 23, 2008, 03:52:00 PM
Hunt later! Wrap Now!
:D :D :D
Good luck out there Doc!
Post by: elk ninja on October 23, 2008, 07:39:00 PM
Nitpicky I know, and for this application, a bit of worthless knowledge.
Great cord along though!
Mike
Post by: tippit on October 23, 2008, 09:07:00 PM
(http://img.photobucket.com/albums/v110/tippit/Knives/Para-cordWrap045.jpg)
Post by: JEFF B on October 23, 2008, 09:21:00 PM
Post by: theunluckyhunter on October 23, 2008, 09:29:00 PM
Post by: tippit on October 23, 2008, 10:50:00 PM
(http://img.photobucket.com/albums/v110/tippit/Knives/Para-cordWrap024.jpg)
Take the loop over the end of the handle back to the original side.
(http://img.photobucket.com/albums/v110/tippit/Knives/Para-cordWrap025.jpg)
Pull the cord tight and go over the looped piece back to the other side. Important thing now is the cord is always under tension so it stays very tight til you finish. Good thing is you will be done in 10 minutes or less!
(http://img.photobucket.com/albums/v110/tippit/Knives/Para-cordWrap027.jpg)
Post by: robtattoo on October 24, 2008, 06:01:00 AM
:D
How'd the hunt go?
Post by: ber643 on October 24, 2008, 07:24:00 AM
Post by: tippit on October 24, 2008, 07:27:00 AM
Final Push:
There are all sorts of wraps and designs you can apply to the handle...just check U-tube. What I like adds a rib down the center of the handle not only giving great grip but adding a fuller rounded feel to the grip.
You twist the cord 2 times and pull it tight Not front to back But side to side. Then take it to the other side and repeat.
Important Points:
1) Always twist the same way. That is right over left or left over right (no difference) BUT once you do the twist...Always repeat it the same way.
2) You will start forming a ridge going up the center of the handle. Keep the line even.
(http://img.photobucket.com/albums/v110/tippit/Knives/Para-cordWrap030.jpg)
(http://img.photobucket.com/albums/v110/tippit/Knives/Para-cordWrap035.jpg)
Keep it tight. Don't worry about getting the layers compressed...that comes next.
(http://img.photobucket.com/albums/v110/tippit/Knives/Para-cordWrap031.jpg)
After going around the handle once on each side, hold you loose ends in one hand (that word again...Tight) and use that piece of wood to compress the wraps down.
(http://img.photobucket.com/albums/v110/tippit/Knives/Para-cordWrap033.jpg)
Now just work your way up the handle compressing the wrap after going around the handle each time.
(http://img.photobucket.com/albums/v110/tippit/Knives/Para-cordWrap036.jpg)
Now hold it...Coffee break.
Post by: tippit on October 24, 2008, 10:45:00 AM
(http://img.photobucket.com/albums/v110/tippit/Knives/Para-cordWrap037.jpg)
To finish just tie a one throw over hand knot...Finished!
(http://img.photobucket.com/albums/v110/tippit/Knives/Para-cordWrap038.jpg)
You can tie off the remaining cord with simple knot or get real fancy with some of the braiding styles. Here is the finished knife in bright yellow and drab green...paracord 550 seven strand core! I was hoping to show another color of bright red but the deer didn't cooperate last night :)
(http://img.photobucket.com/albums/v110/tippit/Knives/Para-cordWrap039.jpg)
(http://img.photobucket.com/albums/v110/tippit/Knives/Para-cordWrap021.jpg)
Last Comment: Why use paracord when you can handle a knife out in something real purrty?
For me a hunting knife is all about the edge and the grip. The texture of paracord is superior when it is wet, slimy, and greasy...kinda like when you dress out a deer, bear, hog, or whatever. It will clean up after field use with hot soapy water but it will carry an odor after too many uses. Not a problem for me cause I can replace it in less than 10 minutes. I do have some purrty handled knives but my knives for the field are all paracord. I need my fingers for surgery so I can buy more steel and paracord :)
Hope you can follow it. Just remember it took you a little while to learn to tie your shoes. This is just a start...now lets see some Real Fancy paracord braided handles. Doc
Post by: Over&Under on October 24, 2008, 11:48:00 AM
Post by: ber643 on October 24, 2008, 12:37:00 PM
Post by: ber643 on October 24, 2008, 06:58:00 PM
Post by: Chris Surtees on October 25, 2008, 02:07:00 AM
I personally have seen 550 cord in 3 colors now: OD, Tan, and Foliage (replacing OD as the Army's based color).
Doc, you would be in heaven if you seen the rolls of 550 we keep on hand. There are only about 5 things the Army issues that I consider must keeps and 550 is at the top. Think I use it almost as much as 100 MPH tape (Army duct tape).
This is an awesome how to!!!
Post by: tradtusker on October 26, 2008, 06:02:00 AM
Post by: elk ninja on October 26, 2008, 08:01:00 PM
Not sure if things have changed, but I do know that there are companies that claim it's 550, but it really isn't mil spec 550....
So if things have changed, I stand corrected.
Either way, a minor difference in terminology and I'm sure that just about everyone would know what you were talking about if you said "550" and it was "450"....
And good build along to go with your great knives!
Mike
Post by: Larry Surtees on October 26, 2008, 08:42:00 PM
Post by: tippit on October 26, 2008, 09:25:00 PM
Post by: tradtusker on October 28, 2008, 04:28:00 AM
it is not 550 with the 7 strands, it has a single braided strand inside and that is filled with nylon i think. but its very strong, rot proof and lasts well.
PM me your address and i send some over.
Post by: Mechslasher on October 28, 2008, 06:53:00 AM
Post by: ber643 on October 28, 2008, 07:14:00 AM
Post by: elk ninja on October 29, 2008, 09:29:00 AM
It really is pretty stupid that I brought it up, sorry for the hyjack, I appologize! It makes no difference. But to further muddy the wallow, British mil spec is quite different than USA mil spec... but rope is rope and it is all good.
Mike
Post by: beaver#1 on October 29, 2008, 11:14:00 AM
Post by: tippit on October 29, 2008, 01:32:00 PM
Post by: JEFF B on November 02, 2008, 09:35:00 PM
Post by: Ray Hammond on November 03, 2008, 06:31:00 PM
Post by: JC on November 17, 2008, 03:24:00 PM
Great tutorial, I'm just surprised you're not doing turks-head knots and all that by now. Must be spending all your time hammering and grinding steel instead of "knitting".
Post by: tippit on November 17, 2008, 08:53:00 PM
Post by: d. ward on November 18, 2008, 06:28:00 AM
Post by: JC on November 18, 2008, 06:54:00 AM
Post by: tippit on November 19, 2008, 06:55:00 AM
Post by: d. ward on November 19, 2008, 01:19:00 PM
Post by: JC on November 19, 2008, 05:12:00 PM
!["[dntthnk]"]("graemlins/dntthnk.gif" "\"\"")
Maybe you could put in a good word for me to Tom and I could come as camp skinner?
Post by: d. ward on November 20, 2008, 06:45:00 AM
Post by: hunt it on November 20, 2008, 05:44:00 PM
Post by: JC on November 20, 2008, 05:59:00 PM