Trad Gang

Main Boards => The Bowyer's Bench => Topic started by: Flem on March 19, 2019, 11:20:30 PM

Title: Vacuum bagging
Post by: Flem on March 19, 2019, 11:20:30 PM
So last summer I said I would share some info on how I press my bows. Thought I better keep my word and since I am semi documenting my swap build, thought this is a good opportunity to do so.
First I want to say that this is only one way to press a bow, no better or worse than any other method, just where I have ended up.

So anyways I start with a vacuum pump.
 [ You are not allowed to view attachments ]
There are lots of plans for these, Joe Woodworker has a big section of examples people have made and they are all much nicer than mine. You need a vacuum pump(bottom left), pressure switch (#1), solenoid valve(#2) and the tanks. You could just run a pump without anything else, but the pump would almost have to run continuously. The tank setup allows for a approx. 10min on/off cycle. I've yet to get a perfect seal with no pump cycling. Thats not to say it can't be done. I'm content with this one, but if I built another, I would not use any plastic tubing or PVC.
Title: Re: Vacuum bagging
Post by: Flem on March 19, 2019, 11:46:17 PM
Speaking of tubing. I started with reinforced vinyl, no good, it doesn't like heat. The green stuff is heat tolerant reinforced rubber (250F). I put a quick disconnect and a check valve in the line, because it nice to be able to pull the vacuum on your bench before going in the hot box. Originally I used the little brass connector to attach the vac line to the bag, but found that it got too hot and weakened the interface with the bag. I replaced it with a nylon bung for a plastic barrel (250F).
 [ You are not allowed to view attachments ]
 [ You are not allowed to view attachments ]
 [ You are not allowed to view attachments ]
Title: Re: Vacuum bagging
Post by: Roy from Pa on March 20, 2019, 04:21:39 AM
Pretty high tech there, Flem.

Looks cool.
Title: Re: Vacuum bagging
Post by: Forwardhandle on March 20, 2019, 09:41:23 AM
Thanks Flem I have been waiting on this one with great interest I have multipal uses for a vac press , that Joe wood workers page is very good I have been looking for a decent vac pump fo the right $$$ but a little skeptical of some I see for cheap & re builts I know you got lucky on the E box store but I'm not much of a gambler looking for some thing new !
Title: Re: Vacuum bagging
Post by: Flem on March 20, 2019, 10:12:32 AM
Pretty high tech there, Flem.

Looks cool.

Hillbilly tech

So where was I when I ran out of beer...
Bags. You need some sort of tubing or membrane to squeeze with. I was using 4mil LDPE tubing, because I had a roll left over from when I was making skis
 [ You are not allowed to view attachments ]
Its a bit wider than I need, but it works. Its about the most common plastic sheeting and its cheap. But above 160F it starts to get soft and distort.
Then I discovered this stuff;
 [ You are not allowed to view attachments ]
Its for food vacuum sealers and its good to 250F. If you look on websites that sell composites, there are lots of materials, some reusable for bagging. I'm still looking for the perfect reusable system. I hate to throw away all that plastic after 1 use.
Since most of you guys make curvy bows, I thought I better lend some relevance to this process, so I got out a old recurve form and put four 3/16" slats on to see how they would bend. They were too long for the form so all 4 overlap in the center, making it 3/4" thick. It looks like it did not pull the tips down all the way, but thats because the excess bag material pinched together before it could suck onto the form.
 [ You are not allowed to view attachments ]
I noticed later that I had left the pressure on the vac set to 12hg for another project. At my elevation I can pull about 25hg.
Title: Re: Vacuum bagging
Post by: skeaterbait on March 20, 2019, 10:50:49 AM
Can you reuse the bags? Would you mind showing some pics of how your hose connects to the bag?
Title: Re: Vacuum bagging
Post by: Flem on March 20, 2019, 12:51:33 PM
Ritchie, I don't blame you for wanting to buy new. I will say my used pump is probably 10yrs old. Guess I got lucky!
Skeater, I have tried to reuse the bags, but it seems like they always get compromised somehow. It really sucks to try to find pinholes! Might have a better chance for reuse if you used a heaver plastic than 4mil.
 
Stupid bag won't work if you don't seal the ends and get a port in it!

I sharpened a piece of copper pipe to cut the port. Its nice when it just  barely stretches over the fitting

 
The bung adapter has a shallow seat on the inside and I replaced the hard rubber washer with 2 nestled O rings, for more grip on the bag, the outside is a soft rubber washer, hard washer and nut.



To seal the ends, there are a few options. Some people use a roll closure, didn't work for me. The setting compound tape works good, but the best closure and cheapest/no waste solution is the impulse sealer.
$15 cheap Chinese POS, but its lasted a long time
Title: Re: Vacuum bagging
Post by: skeaterbait on March 20, 2019, 02:01:03 PM
Thanks
Title: Re: Vacuum bagging
Post by: Shredd on March 20, 2019, 05:58:39 PM
Cool Rig you have there Flem...  Love to see someone else using vacuum bagging...  It is so useful in many applications...   I glue up my forms using a vacuum bag...  No screws to worry about being in the wrong spots...  A lot of guys would cringe at the fact that you only got 12 psi going at 25 hg...  Just goes to show you that you don't need a lot of pressure to make a good bond with epoxy...
Title: Re: Vacuum bagging
Post by: Flem on March 20, 2019, 07:02:02 PM
Thanks Shredd. I concur with everything you stated. I'm always looking for stuff to squeeze, cause it works so well.
12psi sounds so wimpy! I prefer to brag that it generates 1750lbs per Sq. ft :goldtooth:
Title: Re: Vacuum bagging
Post by: Crooked Stic on March 20, 2019, 07:55:57 PM
I think epoxy will bond without pressure.
Title: Re: Vacuum bagging
Post by: Shredd on March 21, 2019, 12:33:27 PM
   That's about 1,100 lb on a 60" bow...  Seems enough to me...   :thumbsup:

   Stic...   Don't think it...  Know it...  Matter of fact the more epoxy you squeeze out the weaker the bond...   Talk to any boat builder about that or just look up info on epoxy...  I think that there is only so much that you can learn from other craftsman and hearsay and then there is the reality of the situation...
Title: Re: Vacuum bagging
Post by: ztontonz on March 21, 2019, 02:38:29 PM
Really interesting setup. Thanks for sharing !
Title: Re: Vacuum bagging
Post by: Crooked Stic on March 21, 2019, 03:47:20 PM
Ok so you got a tire on your Jeep 17 X 10 X 33. It carries 35 psi. air pressure. What is the overall PSF press. ??? :bigsmyl: :bigsmyl:
Title: Re: Vacuum bagging
Post by: Shredd on March 21, 2019, 03:58:36 PM
  144 x 35 =  5,040 lbs.
Title: Re: Vacuum bagging
Post by: Shredd on March 21, 2019, 04:01:14 PM
  A 60" x 1 1/2" bow with 60 psi on it is 5,400 lbs...
Title: Re: Vacuum bagging
Post by: Bvas on March 21, 2019, 05:21:16 PM
  A 60" x 1 1/2" bow with 60 psi on it is 5,400 lbs...
Shredd if you are talking hose forms, then I don’t believe this is completely true. :dunno: Just because the hose has 60psi, doesn’t mean all that pressure is being transferred to the bow. Some of that pressure is used to fill the gap in the form. If it takes say 5-10psi to expand the hose to the form, then you are only applying 50-55psi.
Title: Re: Vacuum bagging
Post by: Roy from Pa on March 21, 2019, 05:41:59 PM
Fugger this weight out for me, Shreddy..

(http://i.imgur.com/BGAAApR.jpg) (https://imgur.com/BGAAApR)
Title: Re: Vacuum bagging
Post by: Flem on March 21, 2019, 05:58:15 PM
This thread sucks! I need to wrap this up. Get it in the bag. I already got enough baggage in my life.
OK, thats all the cliche's I got.
 So I'm not going bore anybody with a glue up. I'll get right to the baggage.
I don't go to much trouble pre-bag. I do use some disposable cauls on the sweeps, just to make sure to get good pressure on the one area that the bag stretches most. Also no need for any tape or strapping to keep things in place, except on the ends to keep things from sliding down.



Once that done, its into the bag. Helps to cut the port hole first, not much room after the blank is in.


Heat seal the ends and its time to suck, which can be done one of two ways. You can close the ball valve, pre-charge the tanks and then get a fast draw down. Or what I prefer, the slow draw down. Turn the pump on and while its pulling, make sure everything stays lined up.



The green material is breather fabric, allows the vacuum to pull along the entire length of the blank. It also sucks up any excess resin. You can buy fancy breather/bleeder fabric, I just use whatever I have laying around that fits the bill.This stuff was some furnace filter material.


I'll say it again, this method is not superior to any other, I like it because its easy and I'm lazy.
I do think it has two advantages over other methods
1)no need to strap or tape the crap out of the blank, the vacuum pulls the blank together from all sides.
    makes it real easy to keep things lined up.
2) For the style of Bows I make, no form needed. For other styles, bottom only. No form= less mass to bring to heat. I preheat to 160deg, after the blank goes in the box it takes about 5min to get back to temp.
Title: Re: Vacuum bagging
Post by: Flem on March 21, 2019, 06:05:10 PM
6 pics max per post.
5min after going in the oven


Baking

I got 15min pump cycling on this one, thats good for me!
Roy, I think you get 1400lbs per sq.ft with C-clamps. You got too much math there for me :knothead:
Title: Re: Vacuum bagging
Post by: Roy from Pa on March 21, 2019, 06:14:16 PM
Ok, I have a deflated balloon that weighs 2 ounces.

I pump 10 PSI of air into it.

Shreddys gonna say it now weighs 150 pounds.

No wonder he catches big fish..

LOL
Title: Re: Vacuum bagging
Post by: Shredd on March 21, 2019, 06:59:35 PM
  A 60" x 1 1/2" bow with 60 psi on it is 5,400 lbs...
Shredd if you are talking hose forms, then I don’t believe this is completely true. :dunno: Just because the hose has 60psi, doesn’t mean all that pressure is being transferred to the bow. Some of that pressure is used to fill the gap in the form. If it takes say 5-10psi to expand the hose to the form, then you are only applying 50-55psi.

   There is very little resistance in the hose to inflate it...  Not enough to be worth mentioning when you are estimating 5,000 lbs what is an extra 1-3 lbs for the weight of the hose???   I would think that it would take less than 1psi to inflate a hose...  I am no Scientist but whatever area the hose comes in contact with and and your gauge reads 60 psi. you are pretty much putting 60 psi on that area...  Thats what psi means, "lbs per sq. inch".
Title: Re: Vacuum bagging
Post by: Shredd on March 21, 2019, 07:06:19 PM
Ok, I have a deflated balloon that weighs 2 ounces.

I pump 10 PSI of air into it.

Shreddys gonna say it now weighs 150 pounds.

No wonder he catches big fish..

LOL

   I guess it depends how dense that air is...  I once caught a very dense mackerel that was only 12" long but weighed 40 lbs. so I had a big cookout and fed 35 people...   :laughing:
Title: Re: Vacuum bagging
Post by: Roy from Pa on March 21, 2019, 07:09:39 PM
I caught a 6 foot northern pike one day.

It was 3 foot up one side and 3 foot down the other side.

 :thumbsup:
Title: Re: Vacuum bagging
Post by: Shredd on March 21, 2019, 07:21:18 PM
     :notworthy:   :biglaugh:    :notworthy:

    Who is this guy??   I think I saw him on Johnny Carson once...
Title: Re: Vacuum bagging
Post by: Fishinglink on March 21, 2019, 08:39:24 PM
Well by Roy’s math I caught an 8’ king salmon once. Only weighed 25#s though.


Sent from my iPhone using Tapatalk
Title: Re: Vacuum bagging
Post by: Crooked Stic on March 21, 2019, 10:21:47 PM
o I got 5040 psf on the inside of my tire and how many Sq. Ft.  :scared: I am surprised that tire aint blowed off the rim by now.
Title: Re: Vacuum bagging
Post by: Flem on March 21, 2019, 10:22:47 PM
I'd like to get ahold of all your stupid fish and crush them with my vacuum. Fiskesuppe anyone?
Title: Re: Vacuum bagging
Post by: Buemaker on March 22, 2019, 05:54:41 AM
Fiskesuppe with shrimps, yummie. ;)
Title: Re: Vacuum bagging
Post by: Roy from Pa on March 22, 2019, 08:29:12 AM
I would think a man living in Montana would be eating elk stew:)

Less he can't shoot for crap:)
Title: Re: Vacuum bagging
Post by: Flem on March 22, 2019, 10:00:33 AM
Fiskesuppe with shrimps, yummie. ;)
Thought I might hook a square head with that one :bigsmyl:

Slow Elk stew.The Woofies got all the fast ones :biglaugh:
Title: Re: Vacuum bagging
Post by: Flem on March 23, 2019, 08:32:24 PM
OK, last installment.
Done cooking, 5hrs@160deg


Out of the bag, got some clean up to do!


Looks like the squeezing was successful



I normally use a peel-ply layer in a addition to the breather fabric. I had run out. I use polyester liner fabric from Joann. Its a lot more work to clean up without it. The peel-ply lets you remove the squeeze out by tearing it off the blank. Spent some time cleaning on this one :knothead:
Title: Re: Vacuum bagging
Post by: Roy from Pa on March 23, 2019, 09:44:58 PM
Nice dude.
Title: Re: Vacuum bagging
Post by: Buemaker on March 24, 2019, 04:28:59 AM
Came out nice, glue lines look good.
Title: Re: Vacuum bagging
Post by: Forwardhandle on March 24, 2019, 06:21:23 AM
Very nice looks good !
Title: Re: Vacuum bagging
Post by: Crooked Stic on March 24, 2019, 06:53:04 AM
That sucked up pretty darn good.  :o